1、描写(SCOPE):
格书适宜于12V4A电源兼容器。
The document is to specify the functional requirements of a 48W switching power supply.
2、键盘输入形态(INPUT CHARACTERISTICS):
2.1显示额定电压(Input Voltage):
&nbಞsp; 固定交流电压(Nominal Voltage):100-240Vac
修改范围图(Variation Range):90-264Vac
2.2填写几率(Input Frequency):
&n🎃bsp;固定频繁(Nominal Freque🃏ncy):50/60Hz
🐲 调低频带宽度(Variation Frequency):47-63Hz
2.3搜索电流大小(Input Current):
当发送交流活动线电压为额定功率值的最高值时,工作输出电阻短路感应电流过载,最好录入讨论会感应电流2A。
2 Arms mꦰax At any input voltage and rated, DC output rated load.
2.4 浪涌电压电流(Inrush Current):
当打出为电机额定功率额定负载,场景体温为25℃,放入240Vac冷态开机♔开关电源时的极大浪涌直流电需小于30A。
30Amps Max. Cold start at 240Vac input,🎉 with rated load and 25℃ambient.
2.5 AC漏电流(Ac Leakage Current):
当手机输入工作电压240Vac时,上限漏电流为0.25mA。
0.25 mA Max At 240Vac input.
3、输送基本特征(OUTPUT CHARACTERISTICS):
3.1输入电机功率(Power Output);
&n✱bsp;  ꦿ;电阻值 最少阻抗 上限载荷 顶值电流量 输出精度最大功率
Voltage Min. Load &n🐽bsp; Max. Load Peak Output Power
+12Vdc 0A 2.5A 🃏4A 30W
3.2阻抗的特点/设定率(Comb🐟ined Load/Line Regulation):
端电压 最低变压器空载电压降 极限满载输出功率 &ꦡnbsp; 波形修正 电机负载修正
Voltage Mi♍n. Voltage &⛄nbsp; Max. Voltage Line Regulation Load Regulation
+12Vdc 12.00V 12.60V &n🎃bsp; ±5% ±5%
3.3波浪纹和燥音(Ripple🅠 And Noise):
公测要求:一些环境下一般运转下,应用示波器下行带宽为20MHz衔接到电动车苹果充电器电线电缆的效果端ꩵ,与此同时效果端 并连一些47uF的钛电极电容器和同一个0.1uF的瓷片电阻。
The ripple and noise are as follows when measure wꦦith Max. Bandwidth of 20MHz and Parallel 47uF/0.1uF,crossed connected at testing point.
𝓀 的电压 大波线大噪音分贝
Voltage Ripple And Noise(Max.)
+12Vdc &nb🔴sp; &nbs🌞p; 120mVp-p
3.4启动♚时准确时间延迟准确时间(Turn On Delay Time):
&nb♎sp; 当导入115Vac和的输出非常大短路电流时,最好启动的时段为2S。
2 second Max. At 115Vac ꦜinput and output Max. Load.
3.5升高时候(Rise Time):
当导入115Vac和工作输出最多负载电阻时最多日期为🎃40mS。
&nb♐sp; 40mS Max. At 115Vac input and output Max. Load.
3.6稳定的时间(Hold Up Time):
当键入1𝔍15V和打出最大程度负荷时,最少实现事件为5mS。
5mS Min. At 115Vac input and output Max.🍎 🔜Load.
3.7利用率(Efficiency):
 ꧑; 当复制粘贴100Vac和模拟输出较大 电流🔴时,最低80%。
80%Mܫin.At 100Vac input and output Max. Load.
当键盘输入240Vac和模拟输出主要环境下🃏时,较大83%。
83%Min.At 240Vac 💮input and output Max. Load.
3.8过冲(Overshoot):
&nꦰbsp; 在开关电源进入或关机的时期,极限15%。
&n🐭bsp;15%Max.Whe🅠n power supply at turn on or turn off.
3.9变压器空载损失不算太大过0.5W.
4、保护好功能性(PROTECTION REQUIREMENT):
4.1漏电集成运放保养:
&nbs✅p; Short Circuit Protection:
♑ 该主机电源提供给器在断路取消时,能日🌃常工作的恢复功能。
The p🌳ower supply will be auto recovered when short circuit faults remove.
&n༒bsp; 4.2短路保护的(Over current Protection):过流发动机故障排出后,开关电源将会自动恢复过来正确办公。
The power supply will be a🔥uto recovered when over curren🌜t faults remove.
4.3过压保护区(Over Voltage Protection)
&nb☂sp; &n🍷bsp; 当输入输出线的电压少于功率线的电压时,电原将爱护,设备故障检测后可以复原正常人的工作。
The power𒈔 supply will not be auto recovered when faults remove.
5、条件让(ENVIRONMENTAL REQUIREMET):
5.1本职工作室温(Operating Temperature):
-20℃~🔯 60℃,过载,正常人工作任务(Full load Normal operation)。
 🎶;&nbs✅p; -20℃to60℃,Full load Normal operation.
5.2储放湿度(Storage Temperature):
-20℃to85℃,带塑料外壳(With package).
5.3工作的水分子含量(Relative Humidity):
5%(0℃)~90%(40℃),72分钟,满负荷,顺利工作任务
5%(0℃)~90%(40℃)RH,72Hrs,Full load Normal operating.
5.4震动问题(Vibration):
𓃲1、考试基准:新国💙际焊工电子元器件常务促进会 Operating: IEC 721-3-3 3M3
5~9Hz,A=1.5mm 运行速度度(9~200Hz,Acceleration 5m/s2) 2、货运(Transportation):
ꦫ IEC 721-3-2 2M2 5-9Hz,A=3.5mm
9~200Hz,减时速Acceleration=5m/S2
200~500HZ,促使度Acceleration=15m/S2
3、心轴振动模式(Axes,10 cycles per axis).
&n✨bsp; 在测试测试进程中未能会出现无期限性的烧坏。
No permanent damage may occur during testing.
在电源开关关掉和封闭后,整机才能治愈到首🅰先因素。
&nbsﷺp; The product has to restors its original situ🎃ation after power off/on.)
5.5跌下检验(Dropping)(Packed):
一种角,五个棱, 几个面。
1 corner,3 eꦗdges, and 6 surfaces
角度76cm Height:76cm
6、安全管理及EMC特殊要求(SAFETY AND EMC REQUIREMENT):
6.1防护:遵循 CCC&nb✱sp; CE SAA FCC GS ROHS规格
6.2直流电(DIELECTRIC STRENGTH)(H-Pot):
&nb▨sp; (H♊-Pot)Primary to secondary),3000Vac/5mA/5s.
7、型式规格(MECHANICAL REQUIREMENT):
7.1硬壳(Enclosure):
&ܫnbsp; 金属外壳长宽比:L115*W47*H32mm
The power supply size L:115*W:47*H:32mm
下一篇: 12V6A电脑电源适配器规格书